SELF-GUARD SG-1000 Bedienungsanleitung Seite 1
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Digitale Videorecorder (DVR) SELF-GUARD SG-1000 herunter. Carboguard 893 SG LT PDS [en] Benutzerhandbuch
- Seite / 2
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Carboguard
®
893 SG
with optional (LT) cure
November 2009 replaces March 2008 1000 (1026)
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and
Carboguard® are registered trademarks of Carboline Company.
Selection & Specification Data
Generic Type
Epoxy polyamide with corrosion inhibitor (zinc
phosphate)
Description
Versatile corrosion resistant coating. Used either
as a primer, intermediate coat, or self-priming
finish over steel and zinc primers. May be
topcoated with itself, or a broad variety of high
performance finish coats. Product also has
surface tolerant properties. Optional (LT) cure for
35°F cure capability.
Features
Ready to apply after mixing; no sweat-in time or
thinning required.
Economical fit for use epoxy
Available in a variety of rapid tint colors
Attractive low sheen for tank exteriors
Used as a primer, intermediate, or finish coat
Power tool cleaned surfaces acceptable
Optional low temperature (LT) cure Part B
VOC compliant to current AIM regulations
Colo
r
Primer color (0700) gray. Variety of other finish
coat colors in rapid tint service. Use Bright White
(T800) for tank exterior finish. See Limitations
when using (LT) cure.
Finish
Low sheen
Primers
Self-priming. May be applied over zinc rich
primers. A mist coat may be required to minimize
bubbling over inorganic zinc rich primers.
Topcoats
Acrylics, Alkyds, Epoxies, Polyurethanes
Dry Film
Thickness
3.0-5.0 mils (75-125 microns) per coat as a primer
or an intermediate. Two coats at 3-5 mils (75-125
microns) per coat may be used direct-to- metal.
4.0-6.0 mils (100-150 microns) per coat as a finish
coat over a primer. Do not exceed 10 mils (250
microns) in a single coat. Excessive film thickness
over inorganic zincs may increase damage during
shipping or erection.
Solids
Content By
Volume
893 SG: 62% ± 2%
893 SG (LT) 63% ± 2%
Theoretical
Coverage
Rate
994 mil ft
2
(24.4 m
2
/l at 25 microns)
331 ft
2
at 3 mils (8.1 m
2
/l at 75 microns)
Allow for loss in mixing and application
V
OC Values
893 SG
As supplied: 2.80 lbs./gal (336 g/l)
Thinned:
15 oz/gal w/ #10: 3.26 lbs./gal (391 g/l)
16 oz/gal w/ #33: 3.31 lbs./gal (397 g/l)
16 oz/gal w/ #236E 2.80 lbs./gal (336 g/l)
16 oz/gal w/ #243E 2.80 lbs./gal (336 g/l)
These are nominal values and may vary slightly
with color.
V
OC Values
893 SG (LT)
As supplied: 2.65 lbs./gal (318 g/l)
Thinned:
15 oz/gal w/ #10: 3.12 lbs./gal (374 g/l)
16 oz/gal w/ #33: 3.17 lbs./gal (380 g/l)
16 oz/gal w/ #236E 2.65 lbs./gal (318 g/l)
16 oz/gal w/ #243E 2.80 lbs./gal (336 g/l)
These are nominal values and may vary slightly
with color.
Dry Temp.
Resistance
Continuous: 200°F (93°C)
Non-Continuous: 250°F (121°C)
Discoloration and loss of gloss is observed above
200°F (93°).
Limitations Epoxies lose gloss, discolor and eventually chalk
in sunlight exposure. LT Cure will cause additional
discoloration as it weathers and/or ages.
Substrates & Surface Preparation
General
Surfaces must be clean and dry. Employ
adequate methods to remove dirt, dust, oil and
all other contaminants that could interfere with
adhesion of the coating.
Steel
For most applications:
SSPC-SP6 to obtain a blast profile of 1.0-2.0
mils (25-50 microns). May also be applied over
SSPC-SP3 for certain applications.
Galvanizing
Galvanizing requires a roughened surface for
optimum adhesion/performance of high build
epoxies. Remove any contaminants per SSPC
SP1; ensure there are no chemical treatments
that may interfere with adhesion; and abrade the
surface to establish a suitable roughness
(typically 1 mil). SSPC-SP7 or SP11 are
acceptable methods.
Concrete
Concrete must be cured 28 days at 75°F (24°C)
and 50% relative humidity or equivalent. Prepare
surfaces in accordance with ASTM D4258
Surface Cleaning of Concrete and ASTM D4259
Abrading Concrete. Voids in concrete may
require surfacing.
Performance Data
Test Method System Results Report #
ASTM D4541
Adhesion
Blasted Steel
2 ct. 893 SG
1600 psi
(Pneumatic)
09453
ASTM D522
Flexibility
Blasted Steel
1 ct. 893 SG
90° bend produced
no cracking, ¾”
Cylindrical Mandrel
Bend
09453
Test reports and additional data available upon written request.
1
2
- Carboguard 1
- 893 SG 1
Inhaltsverzeichnis
Seite 1 - 893 SG
Carboguard®893 SG with optional (LT) cure November 2009 replaces March 2008 1000
Seite 2
Carboguard® 893 SG (with optional LT Cure) November 2009 replaces February 2008 To the best of our knowledge the technical data contained herein is
Weitere Dokumente für Digitale Videorecorder (DVR) SELF-GUARD SG-1000
SELF-GUARD SG-1000 Spezifikationen
(116 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.091 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern